Enter a search term and click .

Adjust shooting options for still photography.

To display shooting settings, press MENU/OK in the photo shooting display and select the A (SHOOTING SETTING) tab.


Choose a scene for use when the auto mode selector lever is rotated to w (aAuto Mode).


Adjust settings for the various drive modes.

Option Description
Choose the settings used when the drive dial is rotated to BKT1 or BKT2 (aBracketing).

Select the frame rate used when the drive dial is rotated to CH (high-speed burst) (aContinuous Shooting (Burst Mode)).


Select the frame rate used when the drive dial is rotated to CL (low-speed burst) (aContinuous Shooting (Burst Mode)).


Adjust multiple exposure options for use when the drive dial is rotated to j (multiple exposure) (aMultiple Exposures).

Choose the filter used when the drive dial is rotated to Adv.1 or Adv.2 (aAdvanced Filters).


Each time the shutter button is pressed, the camera takes three shots, varying exposure each time, and combines them into a single picture. The resulting photograph preserves details in highlights and shadows. Follow the steps below to take HDR photos.

  1. Rotate the auto mode selector lever to v.

  2. Rotate the drive dial to S (Single frame).

  3. Select ASHOOTING SETTING > HDR in the shooting menu and press MENU/OK.

  4. Choose the amount the brightnesses of the exposures vary.

    Option Description
    OFF HDR disabled.
    AUTO Dynamic range is automatically set to a value of from 200% to 800%.
    200% Dynamic range is set to 200%.
    400% Dynamic range is set to 400%.
    800% Dynamic range is set to 800%.
    800% + Camera settings are adjusted for maximum variation in dynamic range.
  5. Take photographs.

    The camera will create a combined image.

Keep the camera steady.

The desired results may not be achieved in the subject moves or the composition or lighting changes during shooting.

The picture will be cropped a very small amount and the resolution will drop slightly.

Mottling may appear in pictures taken at higher values. Choose a value according to the scene.

“Extended” sensitivity values are not supported.

Depending on the options selected for HDR and sensitivity, pictures may not be taken at the selected shutter speed.

The flash does not fire.

HDR images are indicated by a t icon during playback.


Take pictures using the crop in the center of the display. Choose this option for pictures of athletes, birds, and other moving subjects.

Option Description
ON Pictures are taken using a 1.25× crop, reducing the picture angle by an amount equivalent to increasing lens focal length by 1.25×; the crop is shown by a frame in the display.
OFF The 1.25× crop is disabled.

The HIMAGE QUALITY SETTING > IMAGE SIZE item in the shooting menu is fixed at P.

The sports finder is not available in modes that offer an electronic shutter.


To reduce the lag between your pressing the shutter button all the way down and the resulting picture being recorded to the memory card, the camera starts shooting with the electronic shutter when the shutter button is pressed halfway and saves a series shots starting just before the shutter button is pressed the rest of the way down.


Pre-shot photography is available only when sELECTRONIC SHUTTER is selected in CH (high speed burst) drive mode (aSHUTTER TYPE).


Choose a shutter release delay.

Option Description
R2 SEC The shutter is released two seconds after the shutter button is pressed. Use to reduce blur caused by the camera moving when the shutter button is pressed. The self-timer lamp blinks as the timer counts down.
S10 SEC The shutter is released ten seconds after the shutter button is pressed. Use for photographs in which you wish to appear yourself. The self-timer lamp blinks immediately before the picture is taken.
OFF Self-timer off.

If an option other than OFF is selected, the timer will start when the shutter button is pressed all the way down. The display shows the number of seconds remaining until the shutter is released. To stop the timer before the picture is taken, press DISP/BACK.

Stand behind the camera when using the shutter button. Standing in front of the lens can interfere with focus and exposure.

The self-timer turns off automatically when the camera is turned off.


If ON is selected, the chosen self-timer setting will remain in effect after a picture is taken or the camera is turned off.



If ON is selected, the self-timer lamp will light during self-timer photography. Select OFF when shooting night scenes or in other situations in which you would prefer that the lamp remain unlit.



Configure the camera to take photos automatically at a preset interval.

  1. Select ASHOOTING SETTING in the shooting menu, highlight INTERVAL TIMER SHOOTING, and press MENU/OK.

  2. Use the focus stick (focus lever) to choose the interval and number of shots. Press MENU/OK to proceed.

  3. Use the focus stick to choose the starting time and then press MENU/OK. Shooting will start automatically.

Interval timer photography cannot be used at a shutter speed of B (bulb) or with multiple exposure photography. In burst mode, only one picture will be taken each time the shutter is released.

Use of a tripod is recommended.

Check the battery level before starting. We recommend using USB power source (aUSB POWER SUPPLY SETTING).

The display turns off between shots and lights a few seconds before the next shot is taken.

The display can be activated at any time by pressing the shutter button.

To continue shooting until the number of shots taken equals the number of exposures remaining at the time interval-timer photography started, set the number of shots to ∞.


Select ON to automatically adjust exposure during interval-timer photography to prevent it changing dramatically between shots.


Large changes in subject brightness may make exposure appear erratic. We recommend that you choose shorter values for INTERVAL TIMER SHOOTING > INTERVAL with subjects that brighten or dim dramatically during shooting.

In manual mode (mode M), exposure smoothing is only available if an AUTO option is selected for sensitivity.


Choose how the camera meters exposure (aMetering).


Choose the shutter type. Choose the electronic shutter to mute the shutter sound.

Option Description
tMECHANICAL SHUTTER Take pictures with the mechanical shutter.
sELECTRONIC SHUTTER Take pictures with the electronic shutter.
uMECHANICAL+ELECTRONIC The camera chooses the mechanical or electronic shutter according to shooting conditions.

If sELECTRONIC SHUTTER or uMECHANICAL+ELECTRONIC is selected, shutter speeds faster than 1/4000 s can be chosen by rotating the shutter speed dial to 4000 and then rotating the rear command dial.

When using the electronic shutter, note the following:

  • Distortion may be visible in shots of moving subjects.
  • Distortion may also be visible in hand-held shots taken at high shutter speeds; use of a tripod is recommended.
  • Banding and fog may occur in shots taken under fluorescent lights or other flickering or erratic illumination.
  • When taking pictures with the shutter muted (aSHUTTER VOLUME), respect your subjects' image rights and right to privacy.

The following restrictions apply when the electronic shutter is used:

  • “Extended” sensitivity values are not supported
  • Long exposure noise reduction has no effect
  • The flash cannot be used


Reduce flicker in pictures and the display when shooting under fluorescent lighting and other similar light sources.

Option Description
ALL FRAMES Flicker reduction is performed for all frames. Compared to when flicker reduction is performed only on the first frame, the frame advance rate for burst photography will drop.
FIRST FRAME Flicker reduction is performed for the first frame only; in burst photography, the value measured for the first frame in each burst will be used for all subsequent shots. Flicker may be visible during burst photography.
OFF Flicker reduction disabled.

Flicker reduction increases the time needed to record pictures.

OFF is selected for FLICKER REDUCTION when the electronic shutter is used.

Flicker reduction is not available during movie recording.


Reduce blur caused by camera shake or subject motion.

Option Description
LCONTINUOUS + MOTION Image stabilization on. If + MOTION is selected, the camera will adjust shutter speed to reduce motion blur when moving objects are detected.
MSHOOTING + MOTION As above, except that image stabilization is performed only when the shutter button is pressed halfway (focus mode C only) or the shutter is released. If + MOTION is selected, the camera will adjust shutter speed to reduce motion blur when moving objects are detected.
OFF Image stabilization off. Choose this option when using a tripod.

+ MOTION has no effect when sensitivity is set to a fixed value, and may also be unavailable at some other combinations of settings. The effect may vary with lighting conditions and the speed at which the object is moving.

This option is available only with lenses that support image stabilization.

The setting selected with the lens image stabilization switch, if any, takes priority over the setting chosen with the IS mode.

Note that vibration or camera sounds may be noticeable as image stabilization takes effect.


Adjust the camera's sensitivity to light (aSensitivity).


Connect to smartphones running the latest version of the FUJIFILM Camera Remote app. The smartphone can then be used to:

  • Control the camera and take pictures remotely
  • Receive pictures uploaded from the camera
  • Browse the pictures on the camera and download selected pictures
  • Upload location data to the camera

For downloads and other information, visit:

aFUJIFILM Camera Remote