.Lenses
The camera can be used with lenses for the FUJIFILM X-mount.
- Lens Parts
- Lens Care
- Removing Lens Caps
- Attaching Lens Hoods
- Lenses with Aperture Rings
- Lenses with No Aperture Rings
- Lenses with O.I.S. Switches
- Manual Focus Lenses
- Power Zoom Lenses
Lens Parts
ALens hood
BMounting marks
CFocus ring
DZoom ring
EAperture ring
FMounting marks (focal length)
GAperture mode switch
HLens signal contacts
IFront lens cap
JRear lens cap
A XF16-50mmF2.8-4.8 R LM WR lens is used here for illustrative purposes.
Lens Care
- Use a blower to remove dust, then gently wipe with a soft, dry cloth. Any remaining stains can be removed by wiping gently with a piece of Fujifilm lens-cleaning paper to which a small amount of lens-cleaning fluid has been applied.
- Replace the front and rear caps when the lens is not in use.
Removing Lens Caps
Remove lens caps as shown.
Lens caps may differ from those shown.
Attaching Lens Hoods
When attached, lens hoods reduce glare and protect the front lens element.
Lenses with Aperture Rings
At settings other than A, you can adjust aperture by rotating the lens aperture ring (exposure modes A and M).
Aperture ring
Selecting ON for MOVIE OPTIMIZED CONTROLoL disables the aperture ring.
When the aperture ring is set to A, rotate the command dials to adjust aperture.
The Aperture Mode Switch
If the lens has an aperture mode switch, aperture can be adjusted manually by sliding the switch to Z and rotating the aperture ring.
Aperture ring
Aperture mode switch
Lenses with No Aperture Rings
Aperture can be adjusted using the front command dial in modes A (aperture-priority AE) and M (manual).
Aperture control can be reassigned to the rear command dial using DBUTTON/DIAL SETTING > COMMAND DIAL SETTING.
Lenses with O.I.S. Switches
If the lens supports optical image stabilization (O.I.S.), the image stabilization mode can be chosen in the camera menus. To activate image stabilization, slide the O.I.S. switch to ON.
O.I.S. switch
Manual Focus Lenses
-
Slide the focus ring to the front for autofocus.
-
For manual focus, slide the focus ring to the back and rotate it while checking the results in the camera display. The focus distance and depth-of-field indicators can be used to assist manual focus.
Note that manual focus may not be available in all shooting modes.
The Depth-of-Field Indicator
The depth-of-field indicator shows the approximate depth of field (the distance in front of and behind the focus point that appears to be in focus). The indicator is displayed in film format.
Power Zoom Lenses
Zoom can be adjusted on power zoom lenses using the zoom/focus control ring, zoom button, or zoom ring.
Adjusting zoom while the lens is wet makes it easier for water to find its way inside the lens. Wipe any water from the lens before adjusting zoom.
A XF18-120mmF4 LM PZ WR lens is used here for illustrative purposes.
| Control | Description |
|---|---|
AZoom ring |
Rotate the zoom ring to zoom in or out manually. |
BZoom/focus control ring |
Rotate the zoom/focus control ring to zoom in or out using powered zoom. The zoom speed is proportional to the speed with which the ring is rotated. |
CZ/F (zoom/focus) button |
Switch the role of zoom/focus control ring from focus to zoom or vice versa. |
DZoom buttons |
Press a zoom button to zoom in or out at a steady speed using powered zoom. Zoom ends when the button is pressed a second time. |
The Z/F and zoom buttons can be assigned other roles using DBUTTON/DIAL SETTING > POWER ZOOM LENS FUNCTION (Fn) SETTING.
The speed at which zoom can be adjusted via the zoom buttons can be chosen using DBUTTON/DIAL SETTING > LENS ZOOM/FOCUS SETTING.
