Touch Screen Mode

The LCD monitor also functions as a touch screen.

Shooting Touch Controls
Playback Touch Controls

Shooting Touch Controls

To enable touch controls, select ON for DBUTTON/DIAL SETTING > TOUCH SCREEN SETTING > xTOUCH SCREEN SETTING.

LCD Monitor

The operation performed can be selected by tapping the touch screen mode indicator in the display. Touch controls can be used for the following operations:

Mode		Description
	TOUCH SHOOTING	Tap your subject in the display to focus and release the shutter. In burst mode, pictures will be taken while you keep your finger on the display.
	AF AF OFF	If SINGLE AF is selected for focus mode, the camera will focus when you tap your subject in the display. Focus locks at the current distance until you tap the AF OFF icon. If CONTINUOUS AF is selected for focus mode, the camera will initiate focus when you tap your subject in the display. The camera will continue to adjust focus for changes in the distance to the subject until you tap the AF OFF icon. When MANUAL FOCUS is selected for focus mode, you can tap the display to focus on the selected subject using autofocus.
	AREA	Tap to select a point for focus or zoom. The focus frame will move to the selected point.
	OFF	Touch screen mode off.

The behavior of the touch screen varies with the AF mode.

Different touch controls are used during focus zoom (aTouch Controls for Focus Zoom).

To disable touch controls and hide the touch screen mode indicator, select OFF for DBUTTON/DIAL SETTING > TOUCH SCREEN SETTING > xTOUCH SCREEN SETTING.

When ON is selected for DBUTTON/DIAL SETTING > TOUCH SCREEN SETTING > xDOUBLE TAP SETTING, you can zoom in by tapping the monitor twice.

Touch control settings can be adjusted using GAF/MF SETTING > TOUCH SCREEN MODE. For information on the touch controls available during movie recording, see “ Movie Recording (FTOUCH SCREEN MODE)”.

MOVIE OPTIMIZED CONTROLoL

Selecting ON for BMOVIE SETTING > MOVIE OPTIMIZED CONTROLoL or tapping the movie-optimized mode button in the shooting display optimizes the command dials and touch controls for movie recording. This can be used to prevent camera sounds being recorded with movie footage.

Movie-optimized mode button

SHUTTER SPEED
APERTURE
EXPOSURE COMPENSATION
FISO
INTERNAL MIC LEVEL ADJUSTMENT/
EXTERNAL MIC LEVEL ADJUSTMENT
WIND FILTER
STEADY-STATE NOISE REDUCTION

LOW CUT FILTER
HEADPHONES VOLUME
FFILM SIMULATION
FWHITE BALANCE
FIS MODE
FIS MODE BOOST
FFOCUS MODE

Enabling movie-optimized controls disables the aperture ring.

When movie-optimized control is enabled, the movie-optimized mode button can be used to change shooting settings or disable movie-optimized control.

EXTERNAL MIC LEVEL ADJUSTMENT can be set only when an external mic is connected.

Touch Function

Functions can be assigned to the following flick gestures in much the same way as function buttons (aTouch-Function Gestures):

Flick up:T-Fn1
Flick left: T-Fn2
Flick right: T-Fn3
Flick down: T-Fn4

In some cases, touch-function flick gestures display a menu; tap to select the desired option.

Touch-function gestures are disabled by default. To enable touch-function gestures, select ON for DBUTTON/DIAL SETTING > TOUCH SCREEN SETTING > cTOUCH FUNCTION.

Touch Zoom

If the lens supports touch zoom, you can zoom in and out by touching the display. Tap the touch zoom button in the display to enable touch zoom.

Touch zoom is controlled using the buttons in the display.

Button		Description
	Touch zoom	Enable touch zoom.
	Zoom in	Zoom in or out. Touch and hold to zoom in or out at a constant speed.
	Zoom out
	Rocker switch	The camera zooms in or out at a speed corresponding to the position of the rocker switch.
	Disable	Disable touch zoom.

The rate at which the camera zooms in and out in response to the T and W buttons can be selected using DBUTTON/DIAL SETTING > LENS ZOOM/FOCUS SETTING > CONSTANT SPEED ZOOM (Fn).

Playback Touch Controls

When ON is selected for DBUTTON/DIAL SETTING > TOUCH SCREEN SETTING > aTOUCH SCREEN SETTING, touch controls can be used for the following playback operations: