.SET UP
Adjust camera settings.
Qa
Choose a language.
DATE/TIME
Set the date and time.
HOME LOCATION
Choose your time zone from a map.
Press ON/OFF (Screen button 6) to enable or disable daylight saving time.
DATE/TIME
Set the camera clock.
TIME DIFFERENCE
Switch the camera clock instantly from your home time zone to the local time at your destination when traveling.
| Option | Description |
|---|---|
| HOME | Set the camera clock to your home time zone. |
| LOCAL | Set the camera clock to the local time at your travel destination. |
Use LOCAL AREA to choose your home time zone before selecting a local time zone using LOCAL.
LOCAL AREA
Choose the region of your travel destination from a map.
RESET ALL EXCEPT NETWORK SETTINGS
Reset settings other than NETWORK and custom white balance to default values.
Press two RESET (Screen buttons 4 and 6) simultaneously to reset.
FORMAT
Select and format a memory card or USB-connected SSD.
| Options | ||
|---|---|---|
| SLOT1 | SLOT2 | SSD |
Select the media and press two FORMAT (Screen buttons 4 and 6) simultaneously to start formatting.
MAINTENANCE
Perform sensor maintenance and check the condition of the supplied battery.
PIXEL MAPPING
Use this option to reduce bright spots if you notice them in your movie.
Results are not guaranteed.
Be sure the battery is fully charged.
Pixel mapping is not available when the camera temperature is elevated.
Processing may take several tens of seconds.
SENSOR CLEANING
Remove dust from the camera image sensor.
| Option | Description |
|---|---|
| UPDATE NOW | Clean the sensor immediately. |
| CLEAN TIMING | Sensor cleaning will be performed when the camera is turned on or off. |
Even after performing sensor cleaning, dust cannot be completely removed from the camera image sensor.
If the dust cannot be removed, contact your Fujifilm dealer.
BATTERY AGE
Check the battery age for the supplied battery. Age is expressed as a number between 0 and 4. The higher the number, the older the supplied battery.
The older the supplied battery, the faster it loses its charge. We recommend that you purchase a new battery.
COOLING FAN SETTING
Set the camera’s cooling fan.
COOLING FAN
Adjust settings for the cooling fan.
| Option | Description |
|---|---|
| AUTO1 | The fan turns on automatically as required when camera temperature rises and runs at slow speed. |
| AUTO2 | The fan turns on and automatically operates from low speed to high speed in order when camera temperature rises. The increased fan noise may be audible in movies. |
| LOW | Run the fan continuously at low speed. |
| HIGH | Run the fan continuously at high speed. The increased fan noise may be audible in movies. |
HIGH MODE SETTING
Adjust the fan speed when the fan runs at high speed.
LOW MODE SETTING
Adjust the fan speed when the fan runs at slow speed.
REC MODE SETTING
Set whether to stop the cooling fan operation when starting movie recording.
| Options | |
|---|---|
| CONTINUE | STOP |
When STOP is selected, the fan runs at high speed automatically during standby.
POWER MANAGEMENT
Set the camera’s power supply.
V Battery Low Warning %
Set the battery level at which the V-mount battery low-level warning is displayed. The level can be set 0% to 100% in 1% increments.
This setting is only valid when using a battery that displays the remaining battery level as a percentage.
V Battery Low Warning V
Set the battery voltage at which the V-mount battery low-level warning is displayed. The voltage can be set from 11.5 V to 17.0 V in 0.1 V increments.
This setting is not valid when using a battery that displays the remaining battery level as a percentage.
LED/SOUND SETTING
TALLY LIGHT SETTING
Set whether to light REC during movie recording. Select ON to light the button.
| Option | Description |
|---|---|
| FRONT | Set whether to light REC on the front. |
| SIDE | Set whether to light REC on the side. |
REC START BEEP
Choose the volume at the start and end of movie recording.
| Options | |||
|---|---|---|---|
| b (high) | c (medium) | d (low) | f (mute) |
LCD SETTING
Configure the display settings for the LCD monitor and the side monitors.
LCD BRIGHTNESS
Adjust the brightness of the display in the LCD monitor.
| Options | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| -5 | -4 | -3 | -2 | -1 | 0 | +1 | +2 | +3 | +4 | +5 |
LCD COLOR
Adjust the saturation of the display in the LCD monitor.
| Options | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| -5 | -4 | -3 | -2 | -1 | 0 | +1 | +2 | +3 | +4 | +5 |
LCD COLOR ADJUSTMENT
Adjust the color of the display in the LCD monitor. Adjust the color of the display on two axes, the R axis and the B axis.
| Options | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| -5 | -4 | -3 | -2 | -1 | 0 | +1 | +2 | +3 | +4 | +5 |
SIDE MONITOR BRIGHTNESS
Adjust the brightness of the display in the side monitors.
| Options | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| -5 | -4 | -3 | -2 | -1 | 0 | +1 | +2 | +3 | +4 | +5 |
SIDE MONITOR COLOR
Adjust the background color of the side monitors.
| Options | |
|---|---|
| LIGHT | DARK |
FIRMWARE UPDATE
Update the firmware (aFirmware Updates).
BODY
Update the firmware of the camera body.
LENS
Update the firmware of the lens attached to the camera.
LCD MONITOR
Update the firmware of the LCD monitor.
MOUNT ADAPTER
Update the firmware of the mount adapter.
REGULATORY
Select SET UP > REGULATORY in the setup menu to view electronic copies of the product model number, FCC/ISED regulatory information, and other certificates.
