This website uses cookies. By using the site you are agreeing to our Privacy Policy.

Enter a search term and click .

Use an optional flash unit for additional lighting when shooting at night or indoors under low light.

  1. Remove the hot shoe cover and slide the flash onto the hot shoe.

  2. Turn the flash on.

    For more information, see the documentation provided with the flash unit.

    The options available vary with the flash unit.

  3. Select FLASH FUNCTION SETTING in the FLASH SETTING menu.

    If the flash is not on, sync terminal options will be displayed. Turn the flash on before adjusting settings.

  4. Highlight items using the selector and rotate the rear command dial to change the highlighted setting.

  5. Press DISP/BACK to put the changes into effect.

Depending on the distance to the subject, some lenses may cast shadows in photos taken with the flash.

The flash will not fire at some settings, for example when the electronic shutter is used.

Choose shutter speeds slower than 250X when using the flash in exposure mode S (shutter-priority AE) or manual (M).

In TTL mode, the flash may fire several times with each shot. Do not move the camera until shooting is complete.

Red-Eye Removal

Red-eye removal is available when an option other than OFF is selected for FLASH SETTING > RED EYE REMOVAL and AF/MF SETTING > FACE/EYE DETECTION SETTING is ON. Red-eye removal minimizes “red-eye” caused when light from the flash is reflected from the subject’s retinas.

Flash Sync Speed

The flash will synchronize with the shutter at shutter speeds of 1/250 s or slower.

Optional Flash Units

The camera can be used with optional FUJIFILM shoe-mounted flash units. Do not use third-party flash units that apply over 300 V to the camera hot shoe.

The Sync Terminal

Use the sync terminal to connect flash units that require a sync cable.

Using Shoe-Mounted Flash Units

External flash units are more powerful than their built-in counterparts. Some support high-speed sync (FP) and can be used at shutter speeds faster than the flash sync speed, while others can function as master flash units controlling remote units via optical wireless flash control.

Test firing may sometimes be unavailable, for example when the camera setup menu is displayed.

Connect the flash unit and select FLASH SETTING > FLASH FUNCTION SETTING in the camera shooting menu to display flash options. The options available vary with the status of the connected unit.

SYNC TERMINAL will be also displayed if an incompatible flash unit or no flash unit is connected.

Third-party studio flash commanders compatible with the FUJIFILM flash system can now be used. For more information, see the documentation provided your studio flash unit.

SHOE MOUNT FLASH

The following options are available with optional shoe-mounted flash units.

Flash control mode

The flash control mode selected with the flash unit. This can in some cases be adjusted from the camera; the options available vary with the flash.

TTL
TTL mode. Adjust flash compensation ().
M
The flash fires at the selected output regardless of subject brightness or camera settings. Output in some cases can be adjusted from the camera ().
MULTI
Repeating flash. Compatible shoe-mounted flash units will fire multiple times with each shot.
The flash does not fire. Some flash units can be turned off from the camera.

Flash compensation/output

The options available vary with flash control mode.

TTL
Adjust flash compensation (the full value may not be applied if the limits of the flash control system are exceeded). In the cases of the EF-X20, EF-20, and EF-42, the selected value is added to the value selected with the flash unit.
M/MULTI
Adjust flash output (compatible units only). Choose from values expressed as fractions of full power, from 1/1 (mode M) or 1/4 (MULTI) down to 1/512 in increments equivalent to 1/3 EV. The desired results may not be achieved at low values if they exceed the limits of the flash control system; take a test shot and check the results.

Flash mode (TTL)

Choose a flash mode for TTL flash control. The options available vary with the shooting mode (P, S, A, or M) selected.

(FLASH AUTO)
The flash fires only as required; flash level is adjusted according to subject brightness. A icon displayed when the shutter button is pressed halfway indicates that the flash will fire when the photo is taken.
(STANDARD)
The flash fires with every shot if possible; flash level is adjusted according to subject brightness. The flash will not fire if not fully charged when the shutter is released.
(SLOW SYNC.)
Combine the flash with slow shutter speeds when photographing portrait subjects against a backdrop of night scenery. The flash will not fire if not fully charged when the shutter is released.

Sync

Control flash timing.

(1ST CURTAIN)
The flash fires immediately after the shutter opens (generally the best choice).
(2ND CURTAIN)
The flash fires immediately before the shutter closes.
(AUTO FP(HSS))
High-speed sync (compatible units only). The camera automatically engages front-curtain high-speed sync at shutter speeds faster than the flash sync speed. Equivalent to 1ST CURTAIN when MULTI is selected for flash control mode.

Zoom

The angle of illumination (flash coverage) for units that support flash zoom. Some units allow the adjustment to be made from the camera. If AUTO is selected, zoom will automatically be adjusted to match coverage to lens focal length.

Lighting

If the unit supports this feature, choose from the options below.

(FLASH POWER PRIORITY)
Gain range by slightly reducing coverage.
(STANDARD)
Match coverage to picture angle.
(EVEN COVERAGE PRIORITY)
Slightly increase coverage for more even lighting.

LED light

Choose how the built-in LED light functions during still photography (compatible units only). It can function as a catchlight (/CATCHLIGHT), as an AF-assist illuminator (/AF ASSIST), or as both a catchlight and an AF-ASSIST illuminator (/AF ASSIST+CATCHLIGHT). Choose OFF to disable the LED during photography.

Number of flashes

Choose the number of times the flash fires each time the shutter is released in MULTI mode. Full value may not be applied if limits of flash control system are exceeded.

Frequency

Choose the frequency at which the flash fires in MULTI mode. Full value may not be applied if limits of flash control system are exceeded.

SUPPLIED FLASH

Displayed when the EF-X8 flash unit supplied with FUJIFILM X-T1 and X-T2 cameras is connected and raised.

Flash control mode

Choose from the following options.

TTL
TTL mode. Adjust flash compensation () and choose a flash mode ().
M
The flash fires at the selected output () regardless of subject brightness or camera settings. Output is expressed in fractions of full power, from 1/1 to 1/64. The desired results may not be achieved at low values if they exceed the limits of the flash control system; take a test shot and check the results.
(COMMANDER)
Choose if the flash is being used to control remote synced flash units, for example as part of a studio flash system.
The flash does not fire. Flash units connected via the sync terminal will still fire when the shutter is released, but can be disabled by lowering the EF-X8 and turning the units off in the flash settings menu.

Flash compensation/output

Adjust flash level. The options available vary with the flash control mode ()

Flash mode (TTL)

Choose a flash mode for TTL flash control. The options available vary with the shooting mode (P, S, A, or M) selected.

(FLASH AUTO)
The flash fires only as required; flash level is adjusted according to subject brightness. A icon displayed when the shutter button is pressed halfway indicates that the flash will fire when the photo is taken.
(STANDARD)
The flash fires with every shot if possible; flash level is adjusted according to subject brightness. The flash will not fire if not fully charged when the shutter is released.
(SLOW SYNC.)
Combine the flash with slow shutter speeds when photographing portrait subjects against a backdrop of night scenery. The flash will not fire if not fully charged when the shutter is released.

Sync

Choose whether the flash is timed to fire immediately after the shutter opens (/1ST CURTAIN) or immediately before it closes (/2ND CURTAIN). 1ST CURTAIN is recommended in most circumstances.

SYNC TERMINAL

The following options are available when no compatible flash unit is connected or if a unit is connected via the sync terminal or uses only the X-contact on the hot shoe.

Flash control mode

Choose from the following options:

M
A trigger signal is transmitted from the sync terminal and hot shoe when a picture is taken. Choose a shutter speed slower than the sync speed; even slower speeds may be required if the unit uses long flashes or has a slow response time.
The sync terminal and hot shoe do not transmit a trigger signal.

Sync

Choose whether the flash is timed to fire immediately after the shutter opens (/1ST CURTAIN) or immediately before it closes (/2ND CURTAIN). 1ST CURTAIN is recommended in most circumstances.

MASTER (OPTICAL)

The options will be displayed if the unit is currently functioning as master flash for FUJIFILM optical wireless remote flash control.

The master and remote units can be placed in up to three groups (A, B, and C) and flash mode and flash level adjusted separately for each group. Four channels are available for communication between the units; separate channels can be used for different flash systems or to prevent interference when multiple systems are operating in close proximity.

Flash control mode (group A)

Flash control mode (group B)

Flash control mode (group C)

Choose flash control modes for groups A, B, and C. TTL% is available for groups A and B only.

TTL
The units in the group fire in TTL mode. Flash compensation can be adjusted separately for each group.
TTL%
If TTL% is selected for either group A or B, you can specify the output of the selected group as a percentage of the other and adjust overall flash compensation for both groups.
M
In mode M, the units in the group fire at the selected output (expressed as a fraction of full power) regardless of subject brightness or camera settings.
MULTI
Choosing MULTI for any group sets all the units in all groups to repeating flash mode. All units will fire multiple times with each shot.
If OFF is selected, the units in the group will not fire.

Flash compensation/output (group A)

Flash compensation/output (group B)

Flash compensation/output (group C)

Adjust flash level for the selected group according to option selected for flash control mode. Note that the full value may not be applied if the limits of the flash control system are exceeded.

TTL
Adjust flash compensation.
M/MULTI
Adjust flash output.
TTL%
Choose the balance between groups A and B and adjust overall flash compensation.

Flash mode (TTL)

Choose a flash mode for TTL flash control.The options available vary with the shooting mode (P, S, A, or M) selected.

(FLASH AUTO)
The flash fires only as required; flash level is adjusted according to subject brightness. A icon displayed when the shutter button is pressed halfway indicates that the flash will fire when the photo is taken.
(STANDARD)
The flash fires with every shot if possible; flash level is adjusted according to subject brightness. The flash will not fire if not fully charged when the shutter is released.
(SLOW SYNC.)
Combine the flash with slow shutter speeds when photographing portrait subjects against a backdrop of night scenery. The flash will not fire if not fully charged when the shutter is released.

Sync

Control flash timing.

(1ST CURTAIN)
The flash fires immediately after the shutter opens (generally the best choice).
(2ND CURTAIN)
The flash fires immediately before the shutter closes.
(AUTO FP(HSS))
High-speed sync (compatible units only). The camera automatically engages front-curtain high-speed sync at shutter speeds faster than the flash sync speed. Equivalent to 1ST CURTAIN when MULTI is selected for flash control mode.

Zoom

The angle of illumination (flash coverage) for units that support flash zoom. Some units allow the adjustment to be made from the camera. If AUTO is selected, zoom will automatically be adjusted to match coverage to lens focal length.

Lighting

If the unit supports this feature, choose from the options below.

(FLASH POWER PRIORITY)
Gain range by slightly reducing coverage.
(STANDARD)
Match coverage to picture angle.
(EVEN COVERAGE PRIORITY)
Slightly increase coverage for more even lighting.

Master

Assign the master flash to group A (Gr A), B (Gr B), or C (Gr C). If OFF is selected, output from the master flash will be held to a level that does not affect the final picture. Available only if the unit is mounted on the camera hot shoe as a master flash for FUJIFILM optical wireless remote flash control in TTL, TTL%, or M mode.

Number of flashes

Choose the number of times the flash fires each time the shutter is released in MULTI mode.

Channel

Choose the channel used by the master flash for communication with the remote flash units. Separate channels can be used for different flash systems or to prevent interference when multiple systems are operating in close proximity.

Frequency

Choose the frequency at which the flash fires in MULTI mode.